Construction loan interest and the reserve
A construction loan charges interest only on what has been drawn, which is why the carry is far less than rate times loan times term. Enter the loan, the rate, the build length and a draw curve, and this estimates the interest reserve the budget needs.
Total interest carried over the build, capitalized monthly. That is 8.4% of the loan amount for costs.
The formula
Worked with the defaults on this page: $30,000,000 drawn straight-line over 24 months is $1,250,000 a month. At 8.0% the interest accrues on a balance that averages $15,778,388, or 52.6% of the loan, for a total of $2,524,542. Capitalized, that takes the balance at completion to $32,524,542. On the S-curve the same loan carries $2,510,885, almost identical, because a symmetric S-curve has the same average draw timing as a straight line.
The simplification, stated plainly: this assumes a fixed rate, draws that follow the curve exactly and land mid-month, interest capitalized monthly from a reserve funded by the loan, and no fees, retainage or lease-up period after completion. It treats the loan as the first money in; if equity funds first, the real carry is lower.
What the number means
The interest reserve is the cost of time. A building produces nothing until it is finished, so every dollar borrowed to build it accrues interest with no income to pay it. The reserve is that interest, budgeted up front and funded by the loan, which is why it shows up in total development cost alongside concrete and permit fees.
The naive version, rate times loan times term, overstates it badly. At the defaults on this page that shortcut says$4,800,000; the draw-weighted answer is about half, because on average only half the loan is outstanding. The gap between those two numbers is why lenders and developers argue about draw schedules.
How professionals use it
- Developers size the interest reserve line in the budget, then stress it: a six-month delay at the end of the build, when the loan is fully drawn, costs far more than six months at the start.
- Lenders check that the reserve is large enough to carry the loan to completion without a rebalancing call on the sponsor, and size it to a rate above today's if the loan floats.
- Construction companies see the schedule turned into dollars: every month of float the general contractor gives back is roughly one month of interest on a nearly fully drawn loan.
- Equity investors use the carry to understand how much of total cost is time rather than building, and how exposed the return is to rate moves.
Where it misleads
The largest omission is lease-up. A multifamily loan does not stop accruing at completion; the building usually carries most of the balance for another 12 to 18 months while it leases, with income ramping slowly. Many budgets fund the reserve through stabilization, not just construction, and a carry that stops at the topping-out understates the real cost.
Two other cautions. Floating-rate loans priced off SOFR can move several hundred basis points across a 24-month build, so run this at the rate cap strike, not today's rate. And the equity-first structure most lenders require means the loan is drawn later than the project, which lowers the carry this tool shows; if your equity is large, model the loan's own draw schedule rather than the project's.
Frequently asked
- What is an interest reserve on a construction loan?
- An interest reserve is a line in the development budget, funded by the loan itself, that pays the construction loan's interest while the building produces no income. The lender draws interest from it each month, so the borrower does not write checks during construction, but the reserve is real money in total development cost and it accrues interest of its own.
- Why is average outstanding balance roughly half the loan?
- Because a construction loan is drawn as work is completed, not funded on day one. With draws spread evenly over the term the balance climbs from zero to the full amount, so the average sits near half of it, plus the capitalized interest. A common shortcut is to budget interest on 50 to 60 percent of the loan for the full term, which is what this calculator is checking.
- Does an S-curve draw schedule reduce interest?
- Less than people expect. A symmetric S-curve, slow at mobilization, fast through structure and slow at finishes, moves money around within the term but its average timing is close to a straight line, so total interest is nearly the same. What does cut interest is equity going in first, a shorter schedule, or a lower rate.
- What does this calculator leave out?
- Origination and exit fees, unused-line fees, retainage, a lease-up period after completion, and floating-rate moves during the term. It assumes a fixed rate, draws that follow the selected curve exactly, and interest capitalized monthly. Use it to size the reserve line before the lender's own draw model replaces it.